Skip to main content

Parts Catalogue

Electronics parts catalogue

30 components, every spec cited to a real datasheet: sensors, displays, MOSFETs, dev boards and more, with pinouts and honest alternatives. Search or filter, then wire a part straight into a Studio design.

30 of 30 parts

  • 🍌LCD

    16×2 LCD (I2C backpack)

    LCD1602 + PCF8574

    16×2 character LCD with a PCF8574 I2C backpack soldered on — turns the classic 16-pin HD44780 parallel interface into 2 wires.

    —Module4 pins
  • Diode

    1N4007

    1N4007

    1A general-purpose rectifier diode, DO-41 — 1000V reverse rating, slow recovery.

    —DO-412 pins
  • Diode

    1N4148

    1N4148

    Small-signal fast-switching diode, DO-35 — 100V, 150mA average, 4ns reverse recovery.

    —DO-352 pins
  • MOSFET

    2N7000

    2N7000

    Small-signal N-channel MOSFET, TO-92 — 60V drain rating and 200mA absolute current ceiling.

    —TO-923 pins
  • Linear / LDO

    AMS1117-3.3

    AMS1117-3.3

    Fixed 3.3V LDO, SOT-223 — 1A max, but budget 1.1-1.3V of dropout headroom above 3.3V.

    3.3VSOT-2233 pins
  • 🍌Arduino

    Arduino Nano

    A000005

    Breadboard-friendly ATmega328P board — same silicon as the Uno, 5V logic, no wireless.

    7–12VModule26 pins
  • Transistor

    BC547

    BC547

    Small-signal NPN BJT, TO-92 — 45V, 100mA, general-purpose switching and amplification.

    —TO-923 pins
  • Pressure

    BME280

    BME280

    I2C temperature + humidity + pressure sensor breakout — the go-to combo environmental sensor.

    —Breakout Board4 pins
  • 🍌Humidity

    DHT22

    AM2302

    Single-wire temperature + humidity sensor — slower and pricier than a DHT11 but noticeably more accurate.

    3.3–6VModule4 pins
  • Temperature

    DS18B20

    DS18B20

    1-Wire digital thermometer, ±0.5°C, configurable 9-12 bit resolution — many can share one data pin.

    3–5.5VTO-923 pins
  • Microcontroller

    ESP32-WROOM-32E

    ESP32-WROOM-32E

    Espressif's WiFi + Bluetooth SoC module — dual-core Xtensa LX6, the same silicon inside most ESP32 dev boards.

    3–3.6VModule38 pins
  • 🍌Distance

    HC-SR04

    HC-SR04

    The classic 4-pin ultrasonic distance sensor — TRIG a pulse, time how long ECHO stays high.

    4.5–5.5VModule4 pins
  • MOSFET

    IRLZ44N

    IRLZ44NPBF

    Logic-level N-channel power MOSFET, TO-220 — 55V, 0.022Ω, 47A, fully enhanced from a 5V gate.

    —TO-2203 pins
  • Driver IC / Module

    L298N Motor Driver Module

    Dual H-bridge motor driver breakout — drives 2 DC motors (or 1 stepper) from digital + PWM pins. Expect ~2V lost per channel under load.

    4.5–7VModule13 pins
  • Buck

    LM2596 Buck Converter Module

    Adjustable step-down module built on the LM2596 — trimpot-set output, wide input range, heavy vendor variance on everything except the chip itself.

    —Module4 pins
  • Linear / LDO

    LM7805

    LM7805

    Fixed 5V linear regulator, TO-220 — 1.5A rated, but heat is the real ceiling, not current.

    5VTO-2203 pins
  • IMU

    MPU-6050

    MPU-6050

    6-axis IMU (3-axis accelerometer + 3-axis gyroscope) with an onboard DMP, on the common GY-521 I2C breakout.

    —Breakout Board8 pins
  • nRF24 / 2.4GHz

    nRF24L01+

    nRF24L01+

    8-pin SPI 2.4GHz radio module with an onboard PCB antenna — the classic cheap point-to-point wireless link between two MCUs.

    1.9–3.6VModule8 pins
  • 🍌Raspberry Pi

    Raspberry Pi Pico

    SC0915

    RP2040-based board — dual Cortex-M0+ at 133MHz, 26 GPIO on a breadboard-friendly 40-pin header, no wireless.

    1.8–5.5VModule40 pins
  • 🍌Servo

    SG90 Servo

    SG90

    Small analog hobby servo sold as SG90 — widely cloned, so verify voltage, current, travel and lead order for the exact unit.

    —Custom3 pins
  • STM32

    STM32F103C8T6 "Blue Pill"

    STM32F103C8T6

    Generic STM32F103C8T6 breakout — 72MHz Cortex-M3, 3.3V logic, most GPIOs 5V-tolerant, notoriously inconsistent clone quality.

    3.3VBreakout Board41 pins

0 of 4 comparison slots selected.

Browse by category

Microcontrollers

1

Bare MCU chips and modules — the die, not the dev board.

Dev Boards

4

Assembled boards you plug in and program: Arduinos, ESP32 kits, Pi Picos.

Sensors

5

Anything that turns a physical quantity into a signal the board can read.

Displays

2

OLEDs, LCDs, e-ink and 7-segment panels.

Communication Modules

2

Wi-Fi, Bluetooth, LoRa and other modules that get data off the board.

Power

4

Regulators, buck/boost converters and battery management.

MOSFETs

2

Voltage-controlled switches for driving motors, LEDs and other loads.

Transistors

1

BJTs, JFETs and Darlingtons — current-controlled switching and gain.

Diodes

2

One-way valves for current: rectifiers, Schottkys, Zeners, TVS.

LEDs

0

Indicator and addressable LEDs.

Resistors

1

Fixed resistors, every tolerance and power rating.

Capacitors

2

Ceramic, electrolytic, tantalum and film capacitors.

Inductors

0

Coils for filtering and switch-mode power supplies.

Connectors

2

Headers, terminal blocks, JST and USB connectors.

Relays

0

Mechanical and solid-state relays for switching higher-power loads.

Motors

2

DC, stepper and brushless motors, plus the drivers that run them.

Memory

0

EEPROM, flash, FRAM and SD storage.

Data Converters

0

ADCs and DACs — the bridge between analog and digital.

Logic ICs

0

Gates, buffers and flip-flops from the 74-series families.

Op-Amps

0

Operational amplifiers for signal conditioning and analog gain.

Audio

0

Buzzers, speakers and microphones.

RF

0

Raw radio parts: transmitters, receivers, antennas, RF amplifiers.

Other

0

Everything that doesn't fit a more specific category yet.

Can't find the part you need?

The catalogue not having a part yet is not a dead end. Describe it in one sentence in the Studio and it wires that part into your design straight from the description.

Describe a part

Frequently asked questions

Where do the specs on this page come from?

Every known value is cited to a datasheet, vendor page, or a direct measurement, never a guess. A field nobody has verified yet is shown as unknown rather than filled in with a plausible-looking number.

What if the part I need is not in this catalogue?

That is not a dead end. Describe the part in one sentence in the Studio and it wires that part into your design from the description, no catalogue entry required first.

What does the banana badge on a part mean?

It means the part has a live in-browser simulation model, so you can exercise your circuit with it before you ever order hardware.

Build it, do not just look it up

Describe your circuit in one sentence and Banana Board wires it to these exact pins, validates it, and lays out a fab-ready PCB.

Start building free