100nF Ceramic Capacitor
100nF X7R ceramic — the standard local decoupling cap for every IC's power pin.
Parts Catalogue
30 components, every spec cited to a real datasheet: sensors, displays, MOSFETs, dev boards and more, with pinouts and honest alternatives. Search or filter, then wire a part straight into a Studio design.
30 of 30 parts
100nF X7R ceramic — the standard local decoupling cap for every IC's power pin.
LCD1602 + PCF8574
16×2 character LCD with a PCF8574 I2C backpack soldered on — turns the classic 16-pin HD44780 parallel interface into 2 wires.
1N4007
1A general-purpose rectifier diode, DO-41 — 1000V reverse rating, slow recovery.
1N4148
Small-signal fast-switching diode, DO-35 — 100V, 150mA average, 4ns reverse recovery.
220Ω fixed resistor — the standard LED current-limiter for a 5V or 3.3V GPIO.
2N7000
Small-signal N-channel MOSFET, TO-92 — 60V drain rating and 200mA absolute current ceiling.
470µF/25V polarized aluminum electrolytic — bulk energy storage on a power rail. Reversed polarity can vent the can.
Two LiPo cells in series: 7.4 V nominal and 8.4 V fully charged.
AMS1117-3.3
Fixed 3.3V LDO, SOT-223 — 1A max, but budget 1.1-1.3V of dropout headroom above 3.3V.
A000005
Breadboard-friendly ATmega328P board — same silicon as the Uno, 5V logic, no wireless.
BC547
Small-signal NPN BJT, TO-92 — 45V, 100mA, general-purpose switching and amplification.
BME280
I2C temperature + humidity + pressure sensor breakout — the go-to combo environmental sensor.
AM2302
Single-wire temperature + humidity sensor — slower and pricier than a DHT11 but noticeably more accurate.
DS18B20
1-Wire digital thermometer, ±0.5°C, configurable 9-12 bit resolution — many can share one data pin.
3.3 V ESP8266 module used as an AT-command Wi-Fi adapter over UART.
30-pin breadboard-friendly ESP32 dev board — WiFi + Bluetooth, 3.3V logic, USB-serial built in.
ESP32-WROOM-32E
Espressif's WiFi + Bluetooth SoC module — dual-core Xtensa LX6, the same silicon inside most ESP32 dev boards.
HC-SR04
The classic 4-pin ultrasonic distance sensor — TRIG a pulse, time how long ECHO stays high.
IRLZ44NPBF
Logic-level N-channel power MOSFET, TO-220 — 55V, 0.022Ω, 47A, fully enhanced from a 5V gate.
B2B-PH-K-S
2-pin, 2.0mm-pitch JST-PH board header — the common LiPo/small-battery connector. Polarity is NOT standardized between vendors.
Dual H-bridge motor driver breakout — drives 2 DC motors (or 1 stepper) from digital + PWM pins. Expect ~2V lost per channel under load.
Adjustable step-down module built on the LM2596 — trimpot-set output, wide input range, heavy vendor variance on everything except the chip itself.
LM7805
Fixed 5V linear regulator, TO-220 — 1.5A rated, but heat is the real ceiling, not current.
MPU-6050
6-axis IMU (3-axis accelerometer + 3-axis gyroscope) with an onboard DMP, on the common GY-521 I2C breakout.
nRF24L01+
8-pin SPI 2.4GHz radio module with an onboard PCB antenna — the classic cheap point-to-point wireless link between two MCUs.
SC0915
RP2040-based board — dual Cortex-M0+ at 133MHz, 26 GPIO on a breadboard-friendly 40-pin header, no wireless.
SG90
Small analog hobby servo sold as SG90 — widely cloned, so verify voltage, current, travel and lead order for the exact unit.
SSD1306
0.96" 128×64 monochrome I2C OLED — no backlight, self-lit pixels, draws more current the more you light up.
STM32F103C8T6
Generic STM32F103C8T6 breakout — 72MHz Cortex-M3, 3.3V logic, most GPIOs 5V-tolerant, notoriously inconsistent clone quality.
16-pin USB-C receptacle — VBUS/GND/CC1/CC2/D+/D-/SBU, no SuperSpeed data. The CC pull-downs are what make a device actually power on.
0 of 4 comparison slots selected.
Bare MCU chips and modules — the die, not the dev board.
Assembled boards you plug in and program: Arduinos, ESP32 kits, Pi Picos.
Anything that turns a physical quantity into a signal the board can read.
OLEDs, LCDs, e-ink and 7-segment panels.
Wi-Fi, Bluetooth, LoRa and other modules that get data off the board.
Regulators, buck/boost converters and battery management.
Voltage-controlled switches for driving motors, LEDs and other loads.
BJTs, JFETs and Darlingtons — current-controlled switching and gain.
One-way valves for current: rectifiers, Schottkys, Zeners, TVS.
Indicator and addressable LEDs.
Fixed resistors, every tolerance and power rating.
Ceramic, electrolytic, tantalum and film capacitors.
Coils for filtering and switch-mode power supplies.
Headers, terminal blocks, JST and USB connectors.
Mechanical and solid-state relays for switching higher-power loads.
DC, stepper and brushless motors, plus the drivers that run them.
EEPROM, flash, FRAM and SD storage.
ADCs and DACs — the bridge between analog and digital.
Gates, buffers and flip-flops from the 74-series families.
Operational amplifiers for signal conditioning and analog gain.
Buzzers, speakers and microphones.
Raw radio parts: transmitters, receivers, antennas, RF amplifiers.
Everything that doesn't fit a more specific category yet.
Can't find the part you need?
The catalogue not having a part yet is not a dead end. Describe it in one sentence in the Studio and it wires that part into your design straight from the description.
Every known value is cited to a datasheet, vendor page, or a direct measurement, never a guess. A field nobody has verified yet is shown as unknown rather than filled in with a plausible-looking number.
That is not a dead end. Describe the part in one sentence in the Studio and it wires that part into your design from the description, no catalogue entry required first.
It means the part has a live in-browser simulation model, so you can exercise your circuit with it before you ever order hardware.
Build it, do not just look it up
Describe your circuit in one sentence and Banana Board wires it to these exact pins, validates it, and lays out a fab-ready PCB.